TECH INFO

So simply...why choose Dampertech - GAZ?

General information regarding the fitment of shock absorbers, suspension struts and lowering kits.
Replacing shock absorbers on any vehicle requires mechanical automotive experience. Under no circumstances should any tool be used to grip the piston rod. This will inevitably produce damage to the smooth surface of the piston rod and torn chamber seals, resulting in fluid loss and an unserviceable unit. Please take time to examine other suspension components during fitment and renew any worn items with suitable replacements.

Suitability
Be sure to check that the parts you are supplied are suitable for the vehicle for which they are intended.We cannot replace any items that have been correctly supplied to the information that we have been given after they have been fitted.

Springs
Please ensure that springs are fitted correctly and not inverted. If you are unable to determine the correct fitting position for your vehicle please refer to your workshop manual or seek guidance from a qualified person.

Brake bias adjustment
Some vehicles that are fitted with a brake bias system may require resetting or adjustment after installation of your new shock absorbers and springs.

Mechanical ABS sensor adjustment
Some vehicles that are fitted with mechanical ABS sensors may require resetting or adjustment after installation of your new shock absorbers and springs.

Steering geometry
Unless Gaz Shocks specify alternative measurements, please use the settings detailed by the manufacturer of the vehicle.

Lowering measurements
The reduction in ride height quoted in our catalogue is approximate and can be affected by many factors that are outside the control of Gaz Shocks. Please ensure that your car has not been subject to any other conversion that may continue to influence it’s ride height after installation and impair the performance of our product.

N.B With some Mercedes models,worn spacers between the coil spring and spring pan may result in excessive lowering. Replacement spacers are readily available from Mercedes Benz spares stockists and should effectively remedy this problem.

Problems associated with excessive lowering
Gaz Shocks recommend that no vehicle is lowered more than 60mm.We will not accept any claim for damage or excessive wear to any component or area of a vehicle however caused.

Vehicles that have had their ride height reduced in excess of 40mm often benefit from having their steering geometry reset to the data detailed by the manufacturer of the vehicle to promote even tyre wear. In some extreme cases even this course of action will not remedy the situation and Gaz Shocks cannot be held responsible for any excessive tyre wear however caused.

After market wheels & tyres
Please ensure that the wheels and tyres fitted to the vehicle will allow enough clearance from the bodywork after installation of the lowering kit. Gaz Shocks are not responsible for any damage to tyres or bodywork caused by friction during contact.

Gaz shocks warranty
Your Gaz Shock is covered by a three year warranty, effective from the date that the shock was purchased. In the unlikely event of a claim under the warranty, the Company will require evidence of purchase. It is a requirement of the Gaz warranty agreement that any faulty unit must be returned to the dealer from whom it was purchased.The dealer will then forward it to the Gaz Quality Department who will assess any relevant claim.The Company will, at its discretion, repair or replace shocks which are part of a valid claim.This warranty will not be valid if there is evidence of incorrect installation or signs that the unit has been tampered with. Units should be returned to the Quality Manager, at the address shown below.

A note giving details of the failure and the conditions prevailing at the time should accompany the unit. Receipt of the unit will be acknowledged and the Company will endeavour to respond within 10 working days.This warranty does not apply if the shock has been used for competition purposes. Gaz Shocks are dedicated to producing Shock Absorbers and Struts that satisfy the exacting requirements of our customers.As part of our Quality System, we are committed to a quality improvement programme and we regard the feedback of our customers as an essential part of this process.

WARNING
Do not over-tighten base control in either direction, as this will result in locking the adjustment on the complete assembly.

Flexibility
Over 30 point rotary adjustments providing the facility for fine tuning without the need to remove the shock absorber from the car.

Revolutionary
Double lip seal plus a further stem seal on the piston rod.
Produces a shock absorber with unrivalled performance characteristics for both the road and track.

Drivability
Employing our complete understanding of every aspect of damping technology we believe that Gaz shock absorbers strike the ultimate balance between comfort and performance roadholding.

Reliability
Every unit is fully tested and dispatched from our factory with an individual dynometer report.

Quality
Made to accredited ISO9001 standard and supplied with a 3 year warranty.

Durability
Zinc plated body that resists salt spray and road grime on vehicles where detailing really matters.

Availability
A full range of fully adjustable shock absorbers and suspension kits for popular models.